The SuperHeroHype Forums

The SuperHeroHype Forums (http://forums.superherohype.com/index.php)
-   Batman World (http://forums.superherohype.com/forumdisplay.php?f=230)
-   -   How to modify a GCFX V1 mask for added accuracy (http://forums.superherohype.com/showthread.php?t=393463)

Banetico 09-16-2012 01:10 PM

How to modify a GCFX V1 mask for added accuracy
 
A lot of people have been PM me with questions on how I did this and that so It shows the video was not detailed enough so here's a list of what I did and how i did it:

this is the video I made for a member here
http://www.youtube.com/watch?v=FaC8i...ature=youtu.be

This is how the mask looked when i first got it:

http://i1217.photobucket.com/albums/...e/IMG_3415.jpg

http://i1217.photobucket.com/albums/...e/IMG_3414.jpg

So... right after I padded the insides using foam sheets:

1-) Using an exacto knife and with REAL care and SLOW movements I removed the sidemost pipes, the 4 thick tubes around the mouth and dremeled, using a sanding drum in high speed, the excess material. I then sanded the parts down with a soft grit sandpaper so leave the surface smooth. I then made the holes on the connectors using the cone shaped sanding stone bit in high speed.

This will not only drill the material out but after a few seconds it will melt the rubber as well so you need to remove the excess fast before it cools off. Be careful not to over do it and ruin the connector piece.

2-) Using hot glue bars I cut them in 3 parts in the correct sizes and angles (each tube and pipe is made of 3 pieces glued together in angles) and when I had made sure they had the right size and angle I heated the sides and glued them to each other (just a tad of heat will do it without melting it too much and creating excess in the angles)

the 4 around the mouth grill where covered in a type of fabric that remind me of how the tubes looked like in the movie, the fabric would be better I know, but it's what i had and made them look way better, I know you can find something even better for them.

The fabric was glued to the assembled pipes with superbonder flex gel (the one with latex infusion) and the fabric stripes had triangle shaped cuts in the angles to allow it to be glued without excess fabric in these areas.

3-) Using a type of 2 parts epoxy modeling clay (used to patch holes and leaks in pipes at home) that hardens to a rock in 10 minutes I molded the new nose sidemost connectors over the mask ones since they're way to look in it. This epoxy will not stick to the rubber so I had to use a mix of E-6000 and superbonder flex for it.

I then proceeded to mold the nose-forehead bridge connector since the one in the mask is too small. it was glued in the same fashion.

4-) I then glued the pipes and tubes to the connectors in the mask using E-6000. (I used a generous amount on each connector.)

5-) Not following the correct logic I spayed a misting of black Krylon Fusion over the entire mask (with a thicker appliance over the top looms as that yellow silver color is horrible!).

once dry I used acrylics for the weathering, with a mixture of blues, browns and boltgun metal each added where I thought was needed according to the picture I was using for reference. the silver and chrome and blue tabs for the top looms is nail enamel dabbed over the pieces and rubbed over with my finger. This will thin it all round and prevent it from breaking with movement of the rubber.

Up to this point I thought I was just going to leave the mask as it was and perhaps sell it and buy a more accurate one like the Gotham FX v2 BUT when I saw the GCFX V2 had the same damned problem with the sidemost nose connectors way too low I decided to mold the front top maw tubes as that was what annoyed me the most from this mask. so...

6-) using the same epoxy putty I measured 4 exact amounts of this material (1 for each tube) and started by molding the middle left one. I had problems with this one because I didn't had something to mold the line recesses in the tube and I spend too much time making sure the correct angled shape was there... The material started hardening and by the time I found something to make the stripes it was too late to make them deep enough. I need to fix this one.

I then molded the front most left one, followed by the sidemost right one and then ending in the leftmost one. the reason for this is that you want the material top end the curing process as far from the one you are working on to avoid boo-boos.

7-) using a fine strip of this epoxy putty I made the grill-tube connector base borders. both on the top and bottom. It's important to note that at least to me, this very small detail really made the mask look "legit" (i can't find a more suitable word)

I then painted the sculpted pieces with nail enamel chrome and finished it with a wash of black acrylic, some brown weathering on the connectors and then proceeded to mist the entire mask with satin finish clear sealant paint.


Ta-Dah!!

http://i1217.photobucket.com/albums/...14898243_n.jpg

http://i1217.photobucket.com/albums/...77694696_n.jpg

http://i1217.photobucket.com/albums/...91886134_n.jpg

http://i1217.photobucket.com/albums/...88282052_n.jpg

http://i1217.photobucket.com/albums/...24126374_n.jpg

Hope this will help everyone!!!

KGC 09-17-2012 12:55 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
Very!
Thank you very much!

KGC 09-17-2012 12:56 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
A tip Bane, also changes the last 2 tubes! ;)

The 4-pipe front, then those who have rebuilt stucco, before applying the new others have them removed?

Banetico 09-18-2012 04:08 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
Quote:

Originally Posted by KGC (Post 24333625)
A tip Bane, also changes the last 2 tubes! ;)

Yep! I plan on changing those 2 as well. then add the wafflewave strips to the sides of the back and the allen screws.

Quote:

Originally Posted by KGC (Post 24333625)
The 4-pipe front, then those who have rebuilt stucco, before applying the new others have them removed?

huh..... what?:confused:

KGC 09-19-2012 02:00 AM

Re: How to modify a GCFX V1 mask for added accuracy
 
Quote:

Originally Posted by Banetico (Post 24340179)
huh..... what?:confused:

Sorry bane, I wanted to tell you if the original tubes were removed before putting the new ones made ​​by you.

Banetico 09-19-2012 05:16 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
haha no problem.

No I didn't removed the original 4 molded in the mask. I sculpted over them.

BaneZero 09-19-2012 09:12 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
n00b question - where do you buy foam sheets and how do you best attach them to the mask (ideally without permanent damage to it/the ability to remove them if necessary)

Thebanewagon 09-20-2012 02:38 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
You're mask looks about a 1000x better man great job really impressive work bud :bow:

Banetico 09-21-2012 02:24 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
Quote:

Originally Posted by BaneZero (Post 24347045)
n00b question - where do you buy foam sheets and how do you best attach them to the mask (ideally without permanent damage to it/the ability to remove them if necessary)

My padding is permanent. I glued it with E-6000 but to hold it in place while the E-6000 cured as it takes about a full hour I added spots of superglue flex (the one with latex imbued in it) to the tips of the padding and a few spots here and there so It would stick to the rubber and allow the rest to dry in place.

The rubber in these masks s pretty damned sturdy. a couple of drops of superglue won't damage it.

the foam sheets I buy them in any place where they sell stuff for seamstress or leather work. At least in my country that's easy to find.

the sheets I buy are about a centimeter thick.

Banetico 09-21-2012 02:25 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
Quote:

Originally Posted by Thebanewagon (Post 24350073)
You're mask looks about a 1000x better man great job really impressive work bud :bow:

Thanks man! I appreciate it!:yay:

Jbane 10-07-2012 09:05 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
Are the mask the are on sale on ebay from GCFX a different version then version 1?

dan148 10-08-2012 03:44 AM

Re: How to modify a GCFX V1 mask for added accuracy
 
Great fix!!

WolframCreative 11-05-2012 04:12 PM

Re: How to modify a GCFX V1 mask for added accuracy
 
The material that was used to make these masks is fairly new, I'm really surprised at how so many people worked with it.


All times are GMT -5. The time now is 11:46 PM.

Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
SuperHeroHype.com, A property of CraveOnline, a divison of AtomicOnline, LLC © 2009 CraveOnline Media, LLC. All Rights Reserved.